Adhesives

1oz Maxi-Cure Extra Thick Cyanoacrylate

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids...

.5oz Insta-Cure+ Medium Gap Filling Cyanoacrylate

Insta-Cure+™ is a higher viscosity CA for loose fitting joints in which the adhesive must bridge gaps. Normally, the thicker CA is applied to one surface and then the parts are held tightly together for about 5 to 15 seconds. For large surface...

IC-LOC Green Wicking Thread Locker (1.69oz.)

IC-LOC™ Green is a thin, medium-high strength threadlock that is applied to fasteners that are already assembled. IC-LOC Green™ wicks down into the threads of fasteners using capillary action and has good performance even with oil coated...

.5oz Insta-Cure Super Thin Cyanoacrylate

Insta-Cure™ has a water-thin viscosity that wicks deep into joints by capillary action and cures in a matter of a few seconds. Surfaces to be bonded must be tight fitting and should be held together while you apply the CA around the edges of the...

Super-Gold+ Gap Filling Medium Foam Safe CA

SUPER-GOLD+™ gap filling medium thickness is our odorless foam safe CA. Is non-frosting and takes only 2 or 3 seconds longer to bond compared to Insta-Cure and Insta-Cure+. There are no fumes that irritate the nose and eyes. SUPER-GOLD+ does not...

Extra Long Extender Tips

Extra Long Extender Tip - #303 For use over the standard #312 top, they provide a rigid tip with extended length to get thin and gap filling CA into hard to reach areas. They are very resistant to clogging and can be cleaned by soaking in acetone.

SLOW-CURE 30-Minute Epoxy (9oz.)

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight...

.5oz Maxi-Cure Extra Thick Cyanoacrylate

Maxi-Cure™ extra thick CA is the best CA for most plastics, including GE’s Lexan MAXI-CURE™ is the best choice for plastic model assembly. When used with INSTA-SET™, it works better than any putty for modifying or filling voids...

Extra Fine Extender Tips

Extra Fine Extender Tip - #302 (6 pcs) For use over the standard #312 top, it allows CowRC's thin CAs (Insta-Cure/Insta-Flex) to be applied a drop at a time. Thin CA tends to run, these allow precise application.

SLOW-CURE 30-Minute Epoxy (4.5oz.)

SLOW-CURE™ 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURE™ can be used for bonding if you’re willing to wait overnight...

QUIK-CURE 5-Minute Epoxy (9oz.)

QUIK-CURE™ 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURE™ shouldn’t be used in areas that are subject to...

FINISH-CURE 20-Minute Finishing Epoxy (4.5oz.)

FINISH-CURE™ 20 min. epoxy is an excellent, low odor substitute for polyester resins. It can be used for applying fiberglass cloth to wood or by itself to give wood a surface ready for primer and paint. FINISH-CURE™ can be sanded, the easiest...